Panzer BOX 200W Mod

Artikelnummer: 730

Kategorie: Akkuträger

Farben

159,00 €
159,00 € pro 1 Set

inkl. 19% USt., versandfreie Lieferung Innerhalb von DE , Versand

Alter Preis: 189,00 €
knapper Lagerbestand

Dieses Produkt hat Variationen. Wählen Sie bitte die gewünschte Variation aus.


Beschreibung

Panzer BOX 200W Mod Powered

By Evolv DNA 200 Chip

One kit contents:

1*Panzer box 200W body

1* USB Cable

1*User Manual

1*Gift Box Packaging

1*3S Li-po 1500mAh battery

Specification:

Weight:226g

Size:92mm*55mm*30mm

Color:Black,white,red,black&White,black&red,red

&white,red&gold(Iron Man edition)

Material:Aluminum Alloy

Panzer box 200W Detailed

Specifications:

Minimum Typical Max

Output Power 1 Watt 200 Watts

Output Voltage 1 Volt 9.0 Volts

Output Current, continuous 50.0 Amps

Output Current, instantaneous peak 55.0 Amps

Atomizer Resistance, temperature sensing

wire, cold

0.08 Ohm 0.4 Ohm 1.0 Ohm

Atomizer Resistance, kanthal wire 0.1 Ohm 0.7 Ohm 2.0 Ohms

Temperature Limit 200°F 450°F 600°F

Input Voltage 9.0 Volts 11.1 Volts 12.6 Volts

Input Current 0.5 Amps 9.0 Amps 23.0 Amps

Screen On Current 18mA

Quiescent Current 4.5 mA

Power Down Current 5uA

Efficiency 97%

Screen size 0.91?

OLED

The Main Functions & Operations

1.1.
Activated Mode&Attaching a new atomizer:To wake the device from power off state, tap the

Fire button. The Panzer200 uses the resistance of the atomizer to calculate the temperature of the

heating coil. It continually looks to see whether a new or changed atomizer has been connected.

If you are using temperature protection, be careful to only attach new atomizers that have cooled to

room temperature to the device. If a new atomizer is attached to the Panzer200 before it has cooled

down, the temperature may read and protect incorrectly until the new atomizer cools.

When you connect a new atomizer or disconnect and reconnect your existing atomizer, the Panzer200

will prompt you to confirm this change. When you fire the first time, before activating the Panzer200

will prompt ?New Coil? LEFT YES/RIGHT NO?. When you see this prompt, if you have attached a

new atomizer, press the LEFT button. If you have disconnected and reconnected the same atomizer,

press the RIGHT button

2.Locked mode:
Pressing the fire button five times with less than .7 seconds between presses will

cause the device to enter Locked mode. In Locked mode, the device will not fire and the output power

will not adjust accidentally. While in Locked mode, the screen will be off, except that pressing a button

will show ?Locked, Click 5X?. To exit Locked mode, press the fire button 5 times.

3.Stealth mode:
While locked, holding the fire and down buttons simultaneously for five seconds will

switch to stealth mode. In this mode the display is off. It will still show error and lock messages. To

switch back to normal display mode, hold down the fire and down buttons simultaneously for 5 seconds.

This setting is stored to internal flash memory, and remains if power is removed.

4.Power Locked mode:
Holding down both the up and down buttons for two seconds will place the

device in Power Locked mode. In this mode, the mod will operate normally, but you will not be able to

change the power setting. This mode prevents accidental power level changes due to the buttons being

pressed while in a pocket. To exit Power Locked mode, hold the up and down buttons for two seconds.

5.
Power Preset Mode:Under the power locked mode,pressing the up/down buttons

twice with less than 0.7 seconds between presses will cause the device to Power

Preset mode,then press the fire button to confirm the selection.

6.Resistance lock:
The Panzer200 relies on the cold resistance of the atomizer to measure temperature

accurately. If the connection is not stable or if you find the measured resistance drifts with time, it may

be desirable to lock the atomizer resistance. To do so, while locked hold both the Fire and Up buttons

for two seconds to enter Resistance Lock mode. In this mode, the Panzer200 will use the present

atomizer cold resistance without refinement until the atomizer is disconnected or the resistance lock is

disabled. A lock symbol will replace the ohm symbol on the display. To disable resistance lock, repeat

the procedure to lock it.

7.Max Temperature Adjust:
From Locked Mode, holding down both the up and down buttons for two

seconds will place the device in Max Temperature Adjust mode. Once this mode is entered, the max

temperature will be displayed. The up and down buttons are used to adjust the max temperature. To

save the new temperature setting and exit, press the Fire button.

Error Messages

The Panzer200 will indicate a variety of error states.

Check Atomizer:
The Panzer200 does not detect an atomizer, the atomizer has shorted out, or the

atomizer resistance is incorrect for the power setting.

Shorted:
The atomizer or wiring are short circuited.

Weak Battery:
The battery needs to be charged, or a higher rate battery needs to be used. If this

happens, the Panzer200 will continue to fire the atomizer, but will not be able to provide the desired

wattage. The Weak Battery message will continue to flash for a few seconds after the end of puff.

Temperature Protected:
The heating coil reached the maximum allowed temperature during the puff.

If this happens, the Panzer200 will continue to fire, but will not be able to provide the desired wattage.

Ohms Too High:
The resistance of the atomizer coil is too high for the current wattage setting. If this

happens, the Panzer200 will continue to fire, but will not be able to provide the desired wattage. The

Ohms Too High message will continue to flash for a few seconds after the end of puff.

Ohms Too Low:
The resistance of the atomizer coil is too low for the current wattage setting. If this

happens, the Panzer200 will continue to fire, but will not be able to provide the desired wattage. The

Ohms Too Low message will continue to flash for a few seconds after the end of puff.

Too Hot:
The Panzer200 has on board temperature sensing. It will shut down and display this message

if the internal board temperature becomes excessive.

Auto power down

The screen will be at full brightness while firing. After 10 seconds with no button presses, the screen

will dim. 30 seconds after the last button press, the screen will fade out and the device will go into sleep

mode. To wake the device, press the fire button.

Charger

The Panzer200 has a built in 1A USB charger. It automatically detects the type of USB power supply it

is connected to, so it can be plugged into standard PC USB ports or higher power chargers. The max

charge current is based on the cell capacity as programmed in Escribe.

Cell-by-cell monitoring

The Panzer200 runs from a three cell battery. Because lithium polymer cells can be damaged by

excessive discharge, with multi-cell series batteries it is important to measure each cell in the battery

independently and stop firing the atomizer when any of the cells reaches the cutoff voltage. The

Panzer200 uses the battery pack taps to monitor each cell.

Cell Balancer

During charging, is vital that none of the batteries charge beyond 4.2 volts per cell. If one of the cells in

the battery has more charge than the others, its voltage will be higher. During charging, the Panzer200

will turn on a ?balancer? to charge that cell slower than the others.

By monitoring and charging each cell individually, the safety of a multi-cell pack is equivalent to using

a single cell. Many products, from power tools to laptops to electric vehicles, use multi-cell packs. All

of them use cell by cell monitoring and balancing to operate safely.

Escribe

Escribe is a software package used to configure and modify the operation of your

Panzer200. It installs on a Windows PC and connects to your Panzer200 using the USB

port.

When you connect your Panzer200 to the PC, press the ?Connect and Download Settings?

button to download the settings presently on your device to Escribe. After you make

changes, press the ?Upload Settings to Device? to save the new settings to the device.


Inhalt: 1,00 Set

Bewertungen (0)

Durchschnittliche Artikelbewertung

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufenscheidung:

Produkt Tags

Bitte melden Sie sich an, um einen Tag hinzuzufügen.


Kunden kauften dazu folgende Produkte
Twisted Aroma - Bottermelk Fresh 10ml

Twisted Aroma - Bottermelk Fresh 10ml

4,50 € *
450,00 € pro 1 l
sofort verfügbar
Bakor Flavor Aroma - Rasputins Bottermelk 10ml

Bakor Flavor Aroma - Rasputins Bottermelk 10ml

7,50 € *
75,00 € pro 100 ml
knapper Lagerbestand
Pharao The Rip Trippers Tank Black

Pharao The Rip Trippers Tank Black

44,90 € *
44,90 € pro 1 Set
sofort verfügbar
PET-Flasche mit verschraubarem Tropfaufsatz 120ml

PET-Flasche mit verschraubarem Tropfaufsatz 120ml

1,99 € *
1,99 € pro 1 Stück
sofort verfügbar
Xtar VC2Plus - 2-Schacht USB-Ladegerät
momentan nicht verfügbar
Grandmas FOGBASE - 1000 ml 3 mg/ml

Grandmas FOGBASE - 1000 ml 3 mg/ml

24,90 € *
24,90 € pro 1 l
knapper Lagerbestand